BSD | BMW Swiches

Make : BMW

Model : 1000RR - K67 

Year : 2019 onward

Part Number : BD-SW-7BC-33

Number of switch functions : 7

Position : left side 

Road or Track : Track only

Mounting type : Mounts directly onto the handlebar using our generic 22mm clamp  

This switch is is a direct 'plug n play' replacement for the standard switch assembly, retaining all controls needed for a track bike but without the controls needed on a road bike. 

Wiring - No modification of the bike wiring is necessary, this kit plugs directly into the connectors of the standard loom via our LIN BUS interface which is programmed to be 100% compatible with the existing

--

Dual Mode operation - The complexity of the standard switch assembly coupled with the ‘doughnut’ wheel make the standard unit not ideally suited to the track.

Our solution was to use a contemporary layout that is familiar to track riders and split up the host of functions into two modes RIDER / SETUP that are switchable at the touch of a button and indicated by an LED

Functions in SETUP mode:   

• Wheel - Navigate left
• Wheel - Navigate right
• Wheel - Navigate up
• Wheel - Navigate down
• Menu - Up
• Menu - Down

Functions in RIDER mode:   

• TC +
• TC -
• DTC on/off
• Flash / lap timer set
• Menu - Up
• Menu - Down

--

Lap timing

GPS – The standard switch provides a manual lap timer ‘start’ via the flash function, this is also recreated on our switch but we also provide an option to plug in a separate GPS lap timer (use pull down menu for this option) which has large memory of built in track finish lines, as well as an easy to set ‘record’ button for creating new finish line positions. 

These 'Type c' switches can mount onto the clutch post or master cylinder, but for BMW applications we provide the BR-G clamp to achieve maximum position adjustment.

One clamp is supplied free with each switch, with the default clamp being the BR-G, but you are free to choose an alternative clamp at the time of ordering at no extra cost. For clutch mounting on the BMW choose clamp CL-A

--

We have clutch clamps for:

• CL-A    32mm in-line bolt spacing 
• CL-B    30mm offset bolt spacing - Brembo XR , GP
• CL-F    30mm in-line as found on Accosato and Hel components
• CL-K    36mm in-line spacing as found on Kawasaki
• CL-J    32mm offset bolts spacing as found on Beringer components
• BR-G    22mm generic bar clamp

Unless otherwise specified we will supply the BR-G clamp for this application.

Clamps may be bought separately should you change this part at a future time, there is no need to replace the switch assembly

Perfect for saving space on the handlebar and ideally suited to bikes with aftermarket brake or clutch parts, or thumb brakes.

--

Construction / Notes: 

• Billet aluminium body
• IP 67 waterproof switches with gold plated contacts
• Raychem type 55 wire and DR25 sleeving
• Plug and play wiring 
• Greater crash protection and electrical integrity
• May be repaired after crash damage
• Custom designs are our speciality, so feel free to ask and typically at no extra cost.
• If you are not sure, call us for advice on 0044 (0)1746 552450.

Make : BMW

Model : 1000RR - K67 

Year : 2019 onward

Part Number : BD-SW-3BC-33

Number of switch functions : 3

Position : Right side 

Road or Track : Track only

Mounting type : Mounts directly onto the brake master cylinder 

This switch is is a direct 'plug n play' replacement for the standard switch assembly, but without the heated grips wiring.

--

Functions :   

• Stop / Run
• Mode
• Start

These 'Type C' switches mount directly onto the brake master cylinder using the two original clamp screws and a new dedicated clamp. 

One clamp is supplied free with each switch, with the default clamp matching the bolt pattern of the standard bike, but you are free to choose an alternative clamp at the time of ordering at no extra cost.

We have brake clamps for:

• BR-A    32mm in-line bolt spacing 
• BR-B    30mm offset bolt spacing - Brembo XR , GP
• BR-N    32mm in-line with a left offset for short brake levers Nissin / Brembo RC, RCS, Costa Corta
• BR-F    30mm in-line as found on Accosato / Hel components
• BR-J     32mm offset bolts spacing as found on Beringer components
• BR-G    Generic clamp for any 21.8 > 22.2 mm handlebar (does not mount on the brake pump)

Unless otherwise specified we will supply the BR-A clamp for this application.

Clamps may be bought separately should you change this part at a future time, there is no need to replace the switch assembly

Perfect for saving space on the handlebar and ideally suited to bikes with aftermarket brake parts