BSD | Honda Switches
£258.00
Make : Honda
Model : CBR1000 RR
Year : 2017 to 2019
Part Number : BD-SW-4B-14
Number of switch functions : 4
Position : Left side
Road or Track : Track only
Mounting type : Clamps around the handlebar via front and rear body - 2 x M4 cap bolts
These traditionally styles race switches mount directly onto the handlebar.
This switch is is a direct 'plug n play' replacement for the standard switch assembly, retaining all controls needed for a track bike but without the controls needed on a road bike.
--
Functions :
Lap set
UP
Down
Mode
Clutch wiring is included
--
Construction / Notes:
Billet aluminium body
IP 67 waterproof switches with gold plated contacts
Raychem type 55 wire and DR25 sleeving
Plug and play wiring
Greater crash protection and electrical integrity
May be repaired after crash damage
Custom designs are our speciality, so feel free to ask and typically at no extra cost.
If you are not sure, call us for advice on 0044 (0)1746 552450
Make : Honda
Model : CBR1000RR (HRC kit only)
Model : 2017 to 2019
Part Number : BD-SW-7BC-01
Number of switch functions : 7
Position : Left side
Road or Track : Track only
Mounting type : Mounts directly onto the handlebar using our generic 22mm clamp
This switch is is a direct 'plug n play' replacement for the standard switch assembly, retaining all controls needed for a track bike but without the controls needed on a road bike.
Only for use with the HRC ECU and wiring.
Rain light switch - This kit only provides the switch and two un-terminated wires for you to connect to your rain light and rain light wiring.
--
Functions :
- Up
- Select
- Down
- Map
- Pit
- Rain switch
- Lap set
--
These 'Type c' switches normally mount onto the clutch post or master cylinder, but Honda only have one clutch post bolt as standard. For this reason the default clamp will be the BR-G generic clamp. This also provides additional clearance for items such as thumb brakes.
One clamp is supplied free with each switch, with the default clamp to suit a standard bike, but you are free to choose an alternative clamp at the time of ordering at no extra cost should you have an aftermarket clutch post.
We have clutch clamps for:
- BR-G 22mm generic bar clamp
- CL-A 32mm in-line bolt spacing
- CL-B 30mm offset bolt spacing - Brembo XR , GP
- CL-F 30mm in-line as found on Accosato and Hel components
- CL-K 36mm in-line spacing as found on Kawasaki
- CL-J 32mm offset bolts spacing as found on Beringer components
Unless otherwise specified we will supply the BR-G clamp for this application.
Clamps may be bought separately should you change the clutch at a future time, there is no need to replace the switch assembly
Perfect for saving space on the handlebar and ideally suited to bikes with aftermarket clutch parts, or thumb brakes.
Make : Honda
Model : CBR1000 RR
Year : 2012 onward
Part Number : BD-SW-3BC-42
Number of switch functions : 3
Position : right side
Road or Track : Track only
Mounting type : Mounts directly onto the brake master cylinder
--
This switch is is a direct 'plug n play' replacement for the standard switch assembly,
**The rain switch is wired for use with the brake light switch circuit.
--
Functions :
- Stop / Run
- Start
- Rain light **
--
These 'Type C' switches mount directly onto the brake master cylinder using the two original clamp screws and a new dedicated clamp.
Alternatively you can use the BR-G clamp to mount directly onto the handlebar.
One clamp is supplied free with each switch, with the default clamp matching the bolt pattern of the standard bike, but you are free to choose an alternative clamp at the time of ordering at no extra cost.
We have clutch clamps for:
- BR-A 32mm in-line bolt spacing
- BR-B 30mm offset bolt spacing - Brembo XR , GP
- BR-N 32mm in-line with a left offset for short brake levers Nissin / Brembo RC, RCS, Costa Corta
- BR-F 30mm in-line as found on Accosato / Hel components
- BR-J 32mm offset bolts spacing as found on Beringer components
- BR-G Generic clamp for any 21.8 > 22.2 mm handlebar (does not mount on the brake pump)
Unless otherwise specified we will supply the BR-A clamp for this application.
Clamps may be bought separately should you change this part at a future time, there is no need to replace the switch assembly
Perfect for saving space on the handlebar and ideally suited to bikes with aftermarket brakes
Make : Honda
Model : CBR1000 RR
Year : 2020 onward
Part Number : BD-SW-6BC-42
Number of switch functions : 6
Road or Track : Track only
Mounting type : Mounts directly onto the handlebar using our generic 22mm clamp
This switch is is a direct 'plug n play' replacement for the standard left switch assembly on bikes equipped with the standard ECU and wiring, including SP models with electronic suspension.
Kit includes:
- 7 function left switch
- Control module
- All wiring to enable 'plug n play'
--
Functions Left:
- Navigate - Up
- Navigate - Down
- Navigate - Left
- Navigate - Right
- Mode
- Lap / Launch
--
These 'Type C' switches mount directly onto the clutch master cylinder using the two original clamp screws and a new dedicated clamp. Or for the left side via a slim 22mm clamp directly onto the handlebar as supplied for this Honda
The clamp is supplied free with each switch, with the default clamp matching the bolt pattern of the standard bike, but you are free to choose an alternative clamp at the time of ordering at no extra cost.
Use the 'pull down' menus above to select alternative clamps
We have brake clamps for:
- BR-A 32mm in-line bolt spacing
- BR-B 30mm offset bolt spacing - Brembo XR , GP
- BR-N 32mm in-line with a left offset for short brake levers Nissin / Brembo RC, RCS, Costa Corta
- BR-F 30mm in-line as found on Accosato / Hel components
- BR-J 32mm offset bolts spacing as found on Beringer components
- BR-G Generic clamp for any 21.8 > 22.2 mm handlebar (does not mount on the brake pump)
Unless otherwise specified we will supply the BR-G clamp for the Honda
Clamps may be bought separately should you change this part at a future time, there is no need to replace the switch assembly
Perfect for saving space on the handlebar and ideally suited to bikes with aftermarket brake or clutch parts, or thumb brakes.
Make : Honda
Model : CBR1000 RR - HRC 'kit'
Year : 2020 onward
Part Number : BD-SW-KIT-40
Number of switch functions - Left : 7
Number of switch functions - Right : 6
Road or Track : Track only
Mounting type - Left : Mounts directly onto the handlebar using our generic 22mm clamp
Mounting type - Right : Mounts directly onto the brake master cylinder
This switch is is a direct 'plug n play' replacement for the standard left and right switch assembly on bikes equipped with the factory HRC 'kit'
The standard right switch is integrated with the throttle grip sensor. To fit this kit you will need to buy the HRC separate throttle sensor which is not supplied in this kit.
Kit includes:
- 7 function left switch
- 6 function right switch
- Control module
- All wiring to enable 'plug n play'
--
Functions Left:
- Pit speed limiter - ON
- Pit speed limiter - OFF
- Mode - A - UP
- Mode - A - DOWN
- Mode - B - UP
- Mode - B - DOWN
- Left control function
Functions Right:
- Launch function
- Stop/Run
- Slick / Wet tyre
- Right control function
- Rain light switch **
- Start
** rain light - This provides the 'switch' only accessed by two spare pins on the main connector. You will need to wire this into the fused power supply of the HRC kit wiring.
--
These 'Type C' switches mount directly onto the brake master cylinder using the two original clamp screws and a new dedicated clamp. Or for the left side via a slim 22mm clamp directly onto the handlebar
The clamp is supplied free with each switch, with the default clamp matching the bolt pattern of the standard bike, but you are free to choose an alternative clamp at the time of ordering at no extra cost.
Use the 'pull down' menus above to select alternative clamps
We have brake clamps for:
- BR-A 32mm in-line bolt spacing
- BR-B 30mm offset bolt spacing - Brembo XR , GP
- BR-N 32mm in-line with a left offset for short brake levers Nissin / Brembo RC, RCS, Costa Corta
- BR-F 30mm in-line as found on Accosato / Hel components
- BR-J 32mm offset bolts spacing as found on Beringer components
- BR-G Generic clamp for any 21.8 > 22.2 mm handlebar (does not mount on the brake pump)
Unless otherwise specified we will supply the BR-A clamp for the brake and the BR-G clamp for the clutch side.
Clamps may be bought separately should you change this part at a future time, there is no need to replace the switch assembly
Perfect for saving space on the handlebar and ideally suited to bikes with aftermarket brake or clutch parts, or thumb brakes.
Make : Honda
Model : CBR1000 SC59
Year : 2008 to 2016
Part Number : BD-SW-2B-18
Number of switch functions : 2
Position : Right side
Road or Track : Both
Mounting type : Clamps around the handlebar via front and rear body - 2 x M4 cap bolts
These traditionally styles race switches mount directly onto the handlebar.
This switch is is a direct 'plug n play' replacement for the standard switch assembly
Brake switch wiring is included
Functions :
- Stop/Run
- Start
Make : Honda
Model : CBR1000 SC59
Year : 2008 to 2016
Part Number : BD-SW-2BC-18
Number of switch functions : 2
Position : Right side
Road or Track : Both
Mounting type : Mounts directly onto the brake master cylinder
--
This switch is is a direct 'plug n play' replacement for the standard switch assembly.
--
Functions :
- Stop/Run
- Start
--
These 'Type C' switches mount directly onto the brake master cylinder using the two original clamp screws and a new dedicated clamp.
One clamp is supplied free with each switch, with the default clamp matching the bolt pattern of the standard bike, but you are free to choose an alternative clamp at the time of ordering at no extra cost.
We have brake clamps for:
- BR-A 32mm in-line bolt spacing
- BR-B 30mm offset bolt spacing - Brembo XR , GP
- BR-N 32mm in-line with a left offset for short brake levers Nissin / Brembo RC, RCS, Costa Corta
- BR-F 30mm in-line as found on Accosato / Hel components
- BR-J 32mm offset bolts spacing as found on Beringer components
- BR-G Generic clamp for any 21.8 > 22.2 mm handlebar (does not mount on the brake pump)
Unless otherwise specified we will supply the BR-A clamp for this application.
Clamps may be bought separately should you change this part at a future time, there is no need to replace the switch assembly
Perfect for saving space on the handlebar and ideally suited to bikes with aftermarket brake components, or narrow bars.
Make : Honda
Model : CBR600
Year : 2007 onward
Part Number : BD-SW-2B-19
Number of switch functions : 2
Position : Right side
Road or Track : Both
Mounting type : Clamps around the handlebar via front and rear body - 2 x M4 cap bolts
These traditionally styles race switches mount directly onto the handlebar.
This switch is is a direct 'plug n play' replacement for the standard switch assembly
Brake switch wiring is included
Functions :
- Stop/Run
- Start
Make : Honda
Model : CBR600
Year : 2007 onward
Part Number : BD-SW-2BC-19
Number of switch functions : 2
Position : Right side
Road or Track : Both
Mounting type : Mounts directly onto the brake master cylinder
--
This switch is is a direct 'plug n play' replacement for the standard switch assembly.
--
Functions :
- Stop/Run
- Start